Skip to main content
Zoom the image with the mouse
Watch Product Video
AXIS A9910 I/0 Relay Expansion Module

| 02862-001

Axis A9910 network I/O relay expansion module with 8 I/O ports, 4 form C wet or dry relay, 4 Modbus sensor ports, PoE support and Axis Edge Vault

£243.00
£291.60 inc VAT
Free delivery on mainland UK and most EU countries. Check delivery charges to where you are.

Connect this relay module to the Axis A9210 device to expand the number of I/Os in your network. Daisy-chain up to 16 devices for 128 I/Os and 64 relays over one PoE cable for a cost-effective solution, with support for environmental Modbus sensors.

  • For use with the Axis A9210 I/O relay module
  • 8 I/O ports
  • 4 form C relay, wet or dry
  • 4 Modbus sensor ports
  • Supports up to 128 I/Os and 64 relays with a single IP connection
  • Axis 5-year warranty, firmware support until 31-12-2031
Hurry! Only left
 

Overview of the Axis A9910 network I/O relay expansion module

  • Extends the functionality of the Axis A9210 network I/O module
  • 8 I/O ports, 4 form C wet/dry relays, and 4 Modbus sensor ports
  • Multidrop technology allows connection for up to 16 of these devices for 128 I/Os and 64 relays
  • Cost-effective PoE connection via A9210 module
  • Based on Axis open platforms such as ACAP and VAPIX support

Easily expand the functionality of Axis and third-party devices even further with this network expansion I/O module, designed for use with the Axis A9210 module. Enable enhanced capabilities with an additional 8 I/O ports, 4 form C wet/dry relays, and 4 Modbus ports for environmental sensors for uses such as temperature and humidity monitoring. Utilise inputs from cameras, analytics, alarm buttons, and audio devices to trigger external devices such as PTZ cameras, lights, alarms or doors. Cost-effective and easy to install, it runs off the PoE connection from the Axis A9210 module.

Recording and Video Management

Recording and video management platforms which will integrate this module:

Example Use Cases

  • Analytics - Trigger external devices including visual and audible alarms on event detection such as unauthorised area access
  • LPR / ANPR gate control - Input from a camera supporting licence plate recognition can lift a gate, barrier or turnstile upon detection
  • Emergency trigger - Activate visual and audible alarms upon pressing of emergency and panic buttons
  • Temperature monitoring - Modbus sensor integrates with environmental sensors including temperature and humidity

Accessories included

  • Expansion module
  • Installation guide
  • Connector kit (mounted)
  • Grounding kit
Back To Top
 

Key technical features of the Axis A9910 network I/O relay expansion module

Network I/O Module

Environment: indoor
Configurable I/Os: I/O: 8x I/O, configurable inputs or outputs
Digital input: 0 to max 30 V DC, possible to supervise between 0–12 V (4 states) a
Programmable end-of-line resistors, 1 K, 2.2 K, 4.7 K and 10 K, 1%, ¼ watt standard
Digital output: Open drain, 0 to max 30 V DC, max 100 mA
Power out I/O: 2x 12 V DC output, combined total max 100 mA
Relays: 4x form C relay, NO/NC, max 4 A, 30 V DC
Power out relay: 12/24 V DC, jumper configurable, max 49.6 W
With DC in: combined total max 4 A at 12 V DC, combined total max 2 A at 24 V DC, max 49.6 W
RS485: 4x port, half duplex, Modbus
Power out RS485: 4x 12 V DC output, combined total max 2 A
Power: Power in: 12–24 V DC, max 90 W
Cable requirements: Wire size for connectors: CSA: AWG 28–16, CUL/UL: AWG 30–14
DC power: AWG 18-16, qualified for up to 3 m (10 ft)
Relay: AWG 18-16, qualified for up to 200 m (656 ft)
I/Os as inputs: AWG 24, qualified for up to 200 m (656 ft)
RS485 data: 1 twisted pair with shield connected to the protected ground, 120 ohm impedance, qualified for up to 1000 m (3281 ft)
RS485 powered by device: AWG 20–16, qualified for up to 200 m (656 ft) c

General

Dimensions: 149mm x 131.8mm x 31.3mm
Weight: 178 g (0.39 lb)
Casing: Steel Colour: white NCS S 1002-B
Mounting: Wall mount
DIN rail mount
Operating temperatures: Temperature: -40 °C to 55 °C (-40 °F to 131 °F)
Conditional maximum temperatured : 70 °C (158 °F)
Humidity: 10–85% RH (non-condensing)
Warranty: 5-year
Firmware support to: 31-12-2031

Frequently bought together with this product

We're here to assist you
Speak to one of our experts, call us on 0151 633 2111